- Home made double biquad wifi antenna how to#
- Home made double biquad wifi antenna password#
- Home made double biquad wifi antenna windows#
The Pi will now be enabled for SSH, and you can connect to it through PuTTY. (5) Eject microSD card from Windows/Mac computer, slip it into Pi, and power-up. (4) Create a new blank text file SSH (SSH.txt if file extensions are shown) in the microSD card’s boot folder. This will open the boot folder of the microSD Card. It is drive (F) in my computer, but may be different letter in your computer. (3) Open Windows/Mac File explorer/File Manager and click on drive pertaining to microSD card. Plug card reader into your Windows/Mac Computer. (2) Slip-out microSD card from Pi, slip it in a card reader.
Home made double biquad wifi antenna windows#
HOW TO SET UP PUTTY IN WINDOWS (A) Enable SSH in PiĪs David Baker has rightly pointed out, first thing you have to do is to enable SSH. The raspberry pi foundation has their own SSH enable walkthrough. You can then type commands in the window and they will run directly on the PiAware computer. It handles the connection from one computer to another through a command window. SSH is a bit more tricky to setup but also allows you to change settings without physically touching the SD card or powering down the raspberry pi. The piaware-config.txt file is where the piaware configuration is stored. These files are for configuration of the Operating system. Did you mean cmdline.txt or config.txt? These are the wrong files. Open the piaware-config.txt file and add the “rfkill yes” to it. You can see this file by taking out the SD card from the Raspberry pi and opening it on your windows machine. The file on the SD card is called piaware-config.txt. Putting in the ip address just gives you a Flight Aware page without any options of looking at files or at what is on the sd card.
Home made double biquad wifi antenna how to#
I have not got a clue where "sudo ifconfig or syslog is, and nor do I know if you are referring to the Raspberry Pi, or the main computer, and if its the Raspberry Pi, so far, there is no direction on how to look into the Rasberry and see those files. I cannot see if the USB WiFi Dongle is working, When I remove the USB WiFi Dongle Flight Aware map still shows aircraft registering. I added piaware-config rfkill yes to the END of the file Reboot and you are back on to using the internal wifi. You can switch back to the internal wifi by setting “rfkill no”. If your piaware was working with the internal wifi then it should now be running through the wifi dongle under the same SSID and password. Plug in the wifi dongle into one of the USB ports This command will just add the rfkill line to the file. OR log into the box through SSH and run the command “piaware-config rfkill yes”. This line will not be in the piaware-config.txt file already and you can add it anywhere in the file. Either pull out the SD card and edit the piaware-config.txt file by added a new line with only “rfkill yes” on it (without the quotes). Here are the steps to make this a bit more clear. eth0 for ethernet adapter and wlan0 for wireless adapters). The ifconfig command will list all the active networking adapters (i.e. Usually connected by either wifi or ethernet. The command “sudo ifconfig” is a command line that works by connect by SSH to the device. How or where do you check for “sudo ifconfig”, does that require pulling out the SD cardĪnd putting into a laptop to view a text config file? The wifi dongle will then be detected and setup with no other changes. You only need to set “rfkill yes” and reboot. Piaware will auto detect and use the USB WiFi Dongle?
Home made double biquad wifi antenna password#
(configuration is loaded from the ssid and password setting)īy setting “rfkill yes” the wifi dongle will load as wlan0 and the wifi dongle will work the same as the internal RPi3 wifi adapter.ĭo you mean that AFTER the change in command line to rfkill yes the Piaware will only configure the wifi adapter on wlan0 to connect to your wifi network. If you deactivate the wifi internal wifi adapter then the external wifi will load as wlan0. The wifi dongle will load on boot as wlan1 if you have the internal Wifi adapter active. Will PiAware automatically use the USB WiFi Dongle or will it require a
0 kommentar(er)
